Many dairy farms now use robotic milking. They allow cows to come to the milking station at any time of the day or night. Data about each cows milk production and number of times milked as well as health information can be gathered through these systems.
There is still work that needs to be done when designing a barn that has robotic milking. Cow traffic patterns, lying down patterns and how the robots will run all need to be considered. Lighting is one of those considerations. If you are looking into building or updating your robotic dairy here are 7 things to consider when selecting dairy farm lights. We also included our recommended ACE LED lighting solutions for each area.
Providing adequate light around the robot, travel paths throughout the barn and standing up to constant cleaning. All while keeping your herd on a light program and not increasing your electric bill.
Here are seven practical considerations for choosing dairy farm lighting for robotic milking systems, along with the ACE LED lighting solutions suited to different areas of a robotic barn.
In a robotic milking barn, cows move between resting areas, feed lanes, water points, and milking stations throughout the day. Unlike a conventional parlor, where staff control much of the movement, a robotic system depends on cows navigating the facility as part of their normal routine.
Lighting should make these routes easy to see and navigate. Alternating bright patches and dark areas, poorly illuminated intersections, and strong shadows can make the environment less predictable for both animals and workers.
A practical lighting plan should provide:
Uniformity matters more than simply increasing brightness. Excessive light in one area does not compensate for a poorly illuminated route elsewhere.
ACE product recommendation: A-HE01 Series Harsh Environment LED Linear Light
The A-HE01 Series is designed for demanding agricultural environments and is well suited to linear lighting layouts along livestock alleys and feed lanes.
Its wide viewing angle and linkable 1-to-N configuration support continuous lighting runs, helping designers distribute light along long routes. Flexible mounting and wiring options also make it easier to accommodate different barn layouts.
The fixture’s finless design and reinforced aluminum heat-dissipation structure address practical concerns associated with dirty, demanding operating environments.
The final fixture spacing and mounting height should be determined through a photometric layout rather than relying on a fixed spacing rule for every barn.
Robotic milking systems use different combinations of cameras, sensors, lasers, and positioning technologies to identify the udder, guide teat-cup attachment, and monitor the milking process.
The lighting requirements depend on the specific equipment. Some vision systems rely on visible light, while others use infrared illumination or other sensing methods. Poorly controlled lighting can affect image quality, particularly where glare, reflections, deep shadows, or temporal flicker interfere with the camera’s exposure.
Before selecting fixtures for the robot area, review the equipment manufacturer’s recommendations for:
Do not assume that brighter lighting will automatically improve robotic performance. The aim is to provide the type and level of illumination specified for the equipment while maintaining good visibility for workers.
ACE product recommendation: A-HE01 Series and VTP Series
The A-HE01 Series can provide general illumination around the robot and along the approach routes. The VTP Series can be considered where a sealed luminaire is needed for a more localized working area.
ACE can help plan fixture positions around the robot layout. However, compatibility with a particular camera or vision system should be confirmed against the robotic equipment manufacturer’s specifications.
The area around a robotic milking unit can be exposed to water, cleaning agents, manure, and high humidity. Depending on the system and farm’s sanitation procedures, fixtures may also receive direct spray during routine cleaning.
A fixture designed for an ordinary warehouse may not withstand these conditions for long. Moisture ingress, deteriorating seals, corrosion, and damaged electrical connections can lead to premature failure and additional maintenance.
When evaluating dairy barn lighting, pay attention to four areas.
Ingress protection. IP66, IP68, and IP69K address different exposure conditions. IP69K is particularly relevant where fixtures are exposed to high-pressure, high-temperature washdown. If immersion protection is also required, check the applicable IP68 specifications separately.
Corrosion resistance. Confirm that the housing, fasteners, brackets, connectors, and seals are suitable for the farm’s cleaning chemicals and environmental conditions.
Easy-to-clean construction. Smooth, sealed housings with fewer exposed recesses make routine cleaning easier and reduce places where dirt and residue can accumulate.
Mechanical protection. Fixtures near gates, livestock, and equipment may require additional impact protection. Verify the IK rating of the specific model where this is a concern.
ACE product recommendations
The actual product configuration, installation method, and cleaning procedure must all be suitable for the conditions at the installation point. A fixture’s IP rating alone does not establish resistance to every disinfectant or chemical.
Robotic milking operates around the clock, but cows still need an appropriate daily lighting schedule.
For lactating dairy cows managed under a long-day lighting program, a commonly used approach is approximately 16 hours of light followed by 8 hours of darkness. The appropriate schedule depends on the herd, production stage, management practices, and veterinary or animal-welfare guidance.
The difficulty in a robotic barn is that milking, monitoring, and maintenance may continue during the intended dark period.
A useful solution is to divide the barn into lighting zones rather than illuminate the entire facility at the same level throughout the day.
For example:
Motion sensors can be useful in selected work areas, but they should not be allowed to create abrupt lighting changes that interfere with the herd’s intended schedule or the robot’s operating requirements.
ACE product recommendation: NSF Series High Bay
The NSF Series offers control options that include 0–10V, DALI-2, sensors, Zigbee, and Bluetooth, depending on the selected configuration.
These options can support zoned lighting and scheduled operation when paired with compatible control equipment. The system should be designed so that control behavior, dimming performance, and light levels are appropriate for both the herd and the robotic equipment.
A smart-control-ready luminaire does not automatically integrate with every farm management platform. Confirm compatibility with the intended controller before specifying the system.
Lighting in a robotic dairy barn may operate for long periods every day. Over time, poor thermal management and low-quality electrical components can contribute to premature failure or declining light output.
Flicker is another consideration. Some forms of temporal light modulation are difficult for people to notice but may affect camera systems, depending on their exposure settings, frame rates, and light-source characteristics.
When comparing products, ask for information on:
ACE product recommendations
The A-HE01 Series uses a reinforced aluminum heat-dissipation structure and a high-quality power supply. Its finless construction is also intended to simplify cleaning in harsh environments.
The NSF Series provides high-output options, with configurations offering luminous efficacy up to 220 lm/W and light output up to 44,000 lumens.
These specifications can help with energy-efficient lighting design, but maximum efficacy and output are configuration-dependent. The actual fixture selection should be based on the required illumination, mounting height, and operating conditions.
For robotic systems that depend on camera-based sensing, request relevant flicker data and confirm that the proposed lighting meets the equipment manufacturer’s requirements.
Automation reduces some manual work, but robotic milking facilities still need regular inspection, cleaning, repairs, and occasional adjustments. Lighting fixtures mounted above gates, robots, and busy livestock routes can be particularly inconvenient to service.
A well-planned installation should account for maintenance access from the beginning.
Consider the following:
ACE product recommendations
The VTP Series uses buckle-clip brackets designed for convenient installation and servicing. Its adjustable orientation can also help direct light toward the working area without changing the entire mounting arrangement.
The A-HE01 Series supports linkable lighting layouts, flexible mounting options, and multiple wiring methods. These features can simplify installation planning along long barn alleys.
The NSF Series is an option for high-ceiling areas where a high-output luminaire is needed. Its mounting position should be selected with both light distribution and future maintenance access in mind.
No lighting installation is entirely maintenance-free. The objective is to reduce avoidable failures and make necessary work safer and more straightforward.
Choosing individual fixtures is only one part of the project. Their placement, mounting height, beam distribution, and control strategy determine how the finished lighting system performs.
A layout designed for a conventional milking parlor may not be suitable for a robotic barn, where cows move freely between resting, feeding, and milking areas.
Before finalizing the specification, consider:
ACE has in-house lighting designers who can help develop customized layouts using the A-HE01, VTP, and NSF Series.
For a new facility, involve the lighting supplier while the barn layout and electrical infrastructure are still being planned. For an existing facility, a site assessment and review of the current lighting system can help identify dark areas, unsuitable fixtures, and opportunities to improve energy efficiency.
The final design should be checked against the requirements of the robotic milking equipment and the farm’s operating practices.
| Barn area | Main lighting requirement | ACE series to consider |
|---|---|---|
| Robot approach and exit routes | Consistent illumination and controlled glare | A-HE01 Series |
| Robotic milking unit | Suitable illumination for the equipment, with washdown protection where required | VTP or A-HE01 Series |
| Washdown-intensive areas | Verified high-pressure washdown protection | VTP or A-HE01 Series, subject to application |
| Long alleys and feed lanes | Linear light distribution and durable construction | A-HE01 Series |
| Large, high-ceiling barns | High output and suitable beam distribution | NSF Series |
| Zoned lighting and scheduled operation | Compatible dimming and control options | NSF Series, subject to configuration |
| Equipment inspection and maintenance | Suitable task lighting and practical access | VTP Series |
This table provides an initial guide. The final selection should be based on the actual environmental exposure, illumination targets, mounting arrangement, and robotic equipment requirements.
ACE offers LED lighting solutions for Industrial Commercial and Agriculture applications. They are able to create their own molds as well as design/develop products and manufacture and inspect their own products. ACE has a CNAS accredited lab and offer OEM/ODM services to many brands in Europe and North America.
There are 3 series of lights that we use for Robotic Dairy applications. The A-HE01 will be used where you have line of lights along the path that the animals will walk. VTP series can be used where there are work areas that need to be sealed off from moisture and NSF series would be used for higher output lights.
We can also provide a light package design service for our customers to determine how many lights and where they should be placed. We can help choose the right optics to suit the application.
When installing lights for robots its best to work with your Robot Supplier on what type of lighting they call for. This will allow us to provide the correct fixtures that will work in the environment and not forget about the cameras and workers or even the herd.
Robotic milking systems depend on more than the robot itself. Cow movement, environmental conditions, equipment performance, and routine maintenance all contribute to the effectiveness of the installation.
A suitable lighting system should provide consistent illumination along cow traffic routes, meet the requirements of cameras and sensors, withstand cleaning procedures, and support the herd’s daily light-dark schedule. It should also be efficient to operate and practical to maintain.
ACE’s A-HE01, VTP, and NSF Series offer different options for these applications, from linear alley lighting to washdown-intensive work areas and high-ceiling barns.
Planning a new robotic dairy barn or upgrading an existing facility?
Explore ACE’s Dairy Farm Lighting Solutions to review the available fixtures and discuss a lighting layout tailored to your project.
ACE provides industrial, commercial, and agricultural LED lighting solutions, with a focus on energy efficiency and demanding operating environments. Its capabilities include in-house research and development, mold design, manufacturing, and quality inspection, supported by a CNAS-accredited laboratory. ACE also provides OEM and ODM services for international lighting brands and offers customized lighting design to meet the requirements of different projects.